50cc wereldsnelheidsrecord bijna verbroken?
- gerwinskreidler
- Berichten: 1517
- Lid geworden op: 30 dec 2006, 19:55
- Locatie: Utrecht
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
50cc wereldsnelheidsrecord bijna verbroken?
Als ik dit zo lees, gaat het Kreidler 50cc wereldrecord er bijna aan.
Gerwin
http://www.miramarevents.com/dreammachi ... liner.html
BuddFab Streamliner Chases World Record
for 50cc Motorcycle
John Buddenbaum is a fabricator by trade, but he couldn't make this up if he tried. En route to building their 50cc racing motorcycle the BuddFab Streamliner, Buddenbaum and his partner Eric Noyes faced an unlikely problem.
The BuddFab Streamliner is on a mission to be the world's fastest 50cc motorcycle
Drag coefficient? No. Faulty parts? Guess again. Fuel leaks. Not even close. The dynamic duo did not account for the thickness of the driver's fire suit and had trouble fitting into the vehicle in the 3/4-inch-thick garment.
With typical good humor, they managed to work it out by raising the roll bar. Now, four years into their racing career, the team has only one modest goal: to make the BuddFab Streamliner the world's fastest 50cc motorcycle by clocking an official time of more than 139 mph.
They are getting close. The team set a new AMA National Record at the 2006 International Motorcycle Speed Trials by BUB held on the Bonneville Salt Flats in Utah, with a flying start one mile two way average of 133.895 mph. If they can add just over 4 mph to their last record performance they will then hold the distinction of having built the fastest 50cc motorcycle ever officially timed.
The challenges do not daunt these motorcycle-racing lifers. Noyes, raised in upstate New York, raced in amateur motocross events throughout the 1970s and go-karts in the ‘80s. Buddenbaum as a child in Northern California “saw an article in Hot Rod Magazine that always stuck with me,„ and competed on California's American Federation of Motorcyclists amateur roadracing circuit from 1976-1981.
Two years ago, Buddenbaum was contracted to build the nose of Mike Akatiff's 900-horsepower streamliner that is currently pursuing a land speed record in Australia, and he was hooked. “I like the building and design of something that comes alive,„ he said. “I like being able to use what I create. I get off on the fact that it works.„
Noyes enjoys “the design and packaging, the rational organization of the parts, and the fact that if you get a record, you may be more clever than some of the others who have tried.„
Buddenbaum and Noyes designed and specially constructed the streamliner in Buddenbaum's fabrication shop in Palo Alto.
It is powered by an Aprilia 50cc (Minarelli AM6 engine) modified with METRAKIT pro race engine parts running on methanol and nitrous oxide. The 13-foot long fiberglass body weighs only 60 pounds, and the frame is 1 1/4-inch by .095-inch mild steel tubing, with stressed aluminum paneling and a full rollcage head to feet — now modified, of course, to allow a 3/4-inch-thick fire suit.
One thing is sure: to paraphrase the old Willie Dixon blues song, the BuddFab “ain't built for comfort, it's built for speed.„
The BuddFab Streamliner will be on display at the Pacific Coast Dream Machines Show on Sunday, April 27 from 10 a.m. to 4 p.m. at Half Moon Bay Airport.
Gerwin
http://www.miramarevents.com/dreammachi ... liner.html
BuddFab Streamliner Chases World Record
for 50cc Motorcycle
John Buddenbaum is a fabricator by trade, but he couldn't make this up if he tried. En route to building their 50cc racing motorcycle the BuddFab Streamliner, Buddenbaum and his partner Eric Noyes faced an unlikely problem.
The BuddFab Streamliner is on a mission to be the world's fastest 50cc motorcycle
Drag coefficient? No. Faulty parts? Guess again. Fuel leaks. Not even close. The dynamic duo did not account for the thickness of the driver's fire suit and had trouble fitting into the vehicle in the 3/4-inch-thick garment.
With typical good humor, they managed to work it out by raising the roll bar. Now, four years into their racing career, the team has only one modest goal: to make the BuddFab Streamliner the world's fastest 50cc motorcycle by clocking an official time of more than 139 mph.
They are getting close. The team set a new AMA National Record at the 2006 International Motorcycle Speed Trials by BUB held on the Bonneville Salt Flats in Utah, with a flying start one mile two way average of 133.895 mph. If they can add just over 4 mph to their last record performance they will then hold the distinction of having built the fastest 50cc motorcycle ever officially timed.
The challenges do not daunt these motorcycle-racing lifers. Noyes, raised in upstate New York, raced in amateur motocross events throughout the 1970s and go-karts in the ‘80s. Buddenbaum as a child in Northern California “saw an article in Hot Rod Magazine that always stuck with me,„ and competed on California's American Federation of Motorcyclists amateur roadracing circuit from 1976-1981.
Two years ago, Buddenbaum was contracted to build the nose of Mike Akatiff's 900-horsepower streamliner that is currently pursuing a land speed record in Australia, and he was hooked. “I like the building and design of something that comes alive,„ he said. “I like being able to use what I create. I get off on the fact that it works.„
Noyes enjoys “the design and packaging, the rational organization of the parts, and the fact that if you get a record, you may be more clever than some of the others who have tried.„
Buddenbaum and Noyes designed and specially constructed the streamliner in Buddenbaum's fabrication shop in Palo Alto.
It is powered by an Aprilia 50cc (Minarelli AM6 engine) modified with METRAKIT pro race engine parts running on methanol and nitrous oxide. The 13-foot long fiberglass body weighs only 60 pounds, and the frame is 1 1/4-inch by .095-inch mild steel tubing, with stressed aluminum paneling and a full rollcage head to feet — now modified, of course, to allow a 3/4-inch-thick fire suit.
One thing is sure: to paraphrase the old Willie Dixon blues song, the BuddFab “ain't built for comfort, it's built for speed.„
The BuddFab Streamliner will be on display at the Pacific Coast Dream Machines Show on Sunday, April 27 from 10 a.m. to 4 p.m. at Half Moon Bay Airport.
-
- Berichten: 78
- Lid geworden op: 04 nov 2007, 19:06
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
sterker nog, sinds 2 september hebben ze het wereldrecord in handen!
Kijk hier maar:
http://www.geocities.com/buddfab/buddfab3
Nog wel onder voorbehoud, de FIM moet nog de officiele goedkeuring verlenen.
Kijk hier maar:
http://www.geocities.com/buddfab/buddfab3
Nog wel onder voorbehoud, de FIM moet nog de officiele goedkeuring verlenen.
-
- Berichten: 78
- Lid geworden op: 04 nov 2007, 19:06
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
Yup, als ik het ook goed begrijp hebben ze dus voldaan aan alle voorwaarden van de FIM.Maarten schreef:Ja, FIM WORLD RECORD 144.966 MPH (233,39 km/uur) als ik het goed begrijp.
Het is echter pas helemaal officieel als ze in Zwitserland een certificaatje in elkaar flansen met een paar stempels en wat handtekeningen...daar is denk ik het wachten op...
- gerwinskreidler
- Berichten: 1517
- Lid geworden op: 30 dec 2006, 19:55
- Locatie: Utrecht
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
-
- Berichten: 191
- Lid geworden op: 10 feb 2006, 22:08
- Locatie: Sint Annaparochie
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
- Contacteer:
-
- Berichten: 78
- Lid geworden op: 04 nov 2007, 19:06
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
Fout, het record was sinds 1981 in Nederlandse handen, rijder Jan Huberts tuner Piet Plompen als ik mij niet vergis, maar niet met een Kreidler...een Casal...Kreidler Team Noord schreef:boeiend, het is al dik 40 jaar geleden dat kreidler het record vestigdegerwinskreidler schreef:Zonde
Niemand van het forum die dat kan verbreken?
dat ze dat nu pas verbeteren met al die technieken en windtunnels ed.
maar toch een mooie prestatie dat wel ik doe het ze in ieder geval niet na
-
- Berichten: 1968
- Lid geworden op: 06 nov 2005, 21:26
- Locatie: omg.Assen
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 1 keer
Inderdaad...een Casal.
zowel als 50cc en als 80cc gereden.
Waarbij de 50cc (als ik mij niet vergis) wel een soort van Kreidler derrivaat was ,namelijk de ex Sparta racemotor van Plompen.
Dat was in feite een soort zelfgefreesd carter met Kreidler spullen erin.
Casal betaalde het feest ,dus in dit geval werd het een Casal motor genoemd.
De 80cc was wel een rasecht Casal blok.
zowel als 50cc en als 80cc gereden.
Waarbij de 50cc (als ik mij niet vergis) wel een soort van Kreidler derrivaat was ,namelijk de ex Sparta racemotor van Plompen.
Dat was in feite een soort zelfgefreesd carter met Kreidler spullen erin.
Casal betaalde het feest ,dus in dit geval werd het een Casal motor genoemd.
De 80cc was wel een rasecht Casal blok.
- Bijlagen
-
- casal segui record do mundo.jpg (71.22 KiB) 29112 keer bekeken
- Luc
- Berichten: 2073
- Lid geworden op: 09 sep 2002, 18:28
- Gegeven waarderingen: 1 keer
- Ontvangen waarderingen: 6 keren
Who knows?mrbillet schreef:Foekema Symmetric Two Stroke? :wink:
groeten Rene
Ik had er nog geen bericht van gekregen, maar dat zal nog wel komen.
Feit is dat het verbroken is, dus wel een historisch moment.
Vorige jaar schreef ik al dat het eraan zat te komen.
De motor is met een turbo op de tailpipe. Eerlijk gezegd vind ik het maar niks, maar goed ze hebben het er wel mee gedaan.
Het vermogen dat je nodig hebt om het te verbreken is niet het belangrijkste.
Bijna alle moderne 50cc racers, zelfs de door 20mm beperkte, zouden het aankunnen.
De fiets en de stroomlijn is hier het belangrijkste. Daarbij komen alle beveiligingen die in USA gelden als tegenwerkende factoren er nog bij.
Zo moet je bvb wel een brandblusser aan boord hebben.
Wel knap als je tijdens zo'n poging tussen door nog even een binnenbrandje blust.
Groeten,
Luc
- Bijlagen
-
- buddfab4i.jpg (40.43 KiB) 29018 keer bekeken
-
- Buddfab1.jpg (61.29 KiB) 29018 keer bekeken
-
- PietPlompen machine
foto gemaakt door Fokko vd Velden - 81wrpietplompen.jpg (51.32 KiB) 29018 keer bekeken
- PietPlompen machine
-
- Berichten: 78
- Lid geworden op: 04 nov 2007, 19:06
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
- Maarten
- Beheerder
- Berichten: 9765
- Lid geworden op: 01 sep 2002, 09:13
- Locatie: Den Haag, Nederland
- Gegeven waarderingen: 833 keren
- Ontvangen waarderingen: 421 keren
- Contacteer:
Nog even de foto's van die site naar onze site kopieeren. Wel interessant allemaal.
Ook het overzicht met 50 cc snelheidsrecordpogingen zal ik aan moeten passen.
viewtopic.php?t=23582
Ook het overzicht met 50 cc snelheidsrecordpogingen zal ik aan moeten passen.
viewtopic.php?t=23582
- Bijlagen
-
- streamliner057.jpg (74.54 KiB) 28796 keer bekeken
-
- streamlinerguts.jpg (56.37 KiB) 28796 keer bekeken
-
- Body-Layout-TBFB.jpg (15.58 KiB) 28796 keer bekeken
- Thijs Leuven
- Berichten: 1778
- Lid geworden op: 09 sep 2006, 21:11
- Locatie: Maastricht
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
- Contacteer:
- Sander.
- Berichten: 2161
- Lid geworden op: 14 dec 2005, 17:40
- Locatie: het Westland, bij Den Haag
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 1 keer
En de recordpoging is gedaan door iemand in zn jeans en trui???? (of is dat alleen maar even voor de foto)Luc schreef:Daarbij komen alle beveiligingen die in USA gelden als tegenwerkende factoren er nog bij.
Zo moet je bvb wel een brandblusser aan boord hebben.
Wel knap als je tijdens zo'n poging tussen door nog even een binnenbrandje blust.
Groeten,
Luc
-
- Berichten: 1268
- Lid geworden op: 02 jul 2004, 22:32
- Locatie: LIESHOUT
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
- Contacteer:
Membraan?? Dus tochLuc schreef:Who knows?mrbillet schreef:Foekema Symmetric Two Stroke?
groeten Rene
Ik had er nog geen bericht van gekregen, maar dat zal nog wel komen.
Feit is dat het verbroken is, dus wel een historisch moment.
Vorige jaar schreef ik al dat het eraan zat te komen.
De motor is met een turbo op de tailpipe. Eerlijk gezegd vind ik het maar niks, maar goed ze hebben het er wel mee gedaan.
Het vermogen dat je nodig hebt om het te verbreken is niet het belangrijkste.
Bijna alle moderne 50cc racers, zelfs de door 20mm beperkte, zouden het aankunnen.
De fiets en de stroomlijn is hier het belangrijkste. Daarbij komen alle beveiligingen die in USA gelden als tegenwerkende factoren er nog bij.
Zo moet je bvb wel een brandblusser aan boord hebben.
Wel knap als je tijdens zo'n poging tussen door nog even een binnenbrandje blust.
Groeten,
Luc