oil leak
-
- Berichten: 6
- Lid geworden op: 28 nov 2022, 02:52
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
oil leak
Hello everyone, i have a 4 speed kreidler engine leaking a lot and all the orings at the kickstarter and gear pedal shaft were new. I can see this is a chronic disease .
Ive read that machining the crankcase and putting a sleeve to host a seal is possible but expensive and putting 2 orings at the kick shaft helps but what do you guys say about this? Its helpless and we must embrace the dripping reallity? Lol..
Anyways if it doesnt drip oil from engine, will drip from the carburetor 2 stroke gas mix from the cold start calling of extra fuel
i had recently put a piston, all seals and gaskets and clutch discs and it was a shame to have to open it again because of this huge leak
thanks in advance
Ive read that machining the crankcase and putting a sleeve to host a seal is possible but expensive and putting 2 orings at the kick shaft helps but what do you guys say about this? Its helpless and we must embrace the dripping reallity? Lol..
Anyways if it doesnt drip oil from engine, will drip from the carburetor 2 stroke gas mix from the cold start calling of extra fuel
i had recently put a piston, all seals and gaskets and clutch discs and it was a shame to have to open it again because of this huge leak
thanks in advance
- Enzo-tvdzijden
- Expert
- Berichten: 60394
- Lid geworden op: 27 nov 2002, 21:55
- Locatie: Gem. Leidschendam/Voorburg
- Gegeven waarderingen: 966 keren
- Ontvangen waarderingen: 2281 keren
-
- Berichten: 6
- Lid geworden op: 28 nov 2022, 02:52
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
Re: oil leak
Hello, what do you mean? It slowly runs from those 2 shafts, after some days there´s a huge puddle just by sitting at the garage. I was surprised singe the orings dont even are bad. the brass bushing has a bit of play but its function is not to seal
- Enzo-tvdzijden
- Expert
- Berichten: 60394
- Lid geworden op: 27 nov 2002, 21:55
- Locatie: Gem. Leidschendam/Voorburg
- Gegeven waarderingen: 966 keren
- Ontvangen waarderingen: 2281 keren
Re: oil leak
direct or indirect gear shifting ?Wrenchmonkey schreef: ↑28 nov 2022, 11:43 Hello, what do you mean? It slowly runs from those 2 shafts, after some days there´s a huge puddle just by sitting at the garage. I was surprised singe the orings dont even are bad. the brass bushing has a bit of play but its function is not to seal
De brass bushing must be no play radial !
Enzo
-
- Berichten: 6
- Lid geworden op: 28 nov 2022, 02:52
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
-
- Berichten: 6
- Lid geworden op: 28 nov 2022, 02:52
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
Re: oil leak
Anyways i have another 3speed Kreidler with underside gear selector, what is the best solution for the leaking?
can we fix it without dismantling the engine?
can we fix it without dismantling the engine?
- Caspar
- Berichten: 13632
- Lid geworden op: 10 sep 2002, 14:43
- Locatie: Zuid-Oost Limburg
- Gegeven waarderingen: 590 keren
- Ontvangen waarderingen: 822 keren
Re: oil leak
A Kreidler doesn't leak oil , it marks it's territory
There is a modification for this problem.
An oil seal on the schift shaft , and an extra O-ring on the kickstarter shaft.
There is a modification for this problem.
An oil seal on the schift shaft , and an extra O-ring on the kickstarter shaft.
-
- Berichten: 6
- Lid geworden op: 28 nov 2022, 02:52
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
Re: oil leak
Could you show me some examples of that modification for the indirect gear shifting mechanism?
- Enzo-tvdzijden
- Expert
- Berichten: 60394
- Lid geworden op: 27 nov 2002, 21:55
- Locatie: Gem. Leidschendam/Voorburg
- Gegeven waarderingen: 966 keren
- Ontvangen waarderingen: 2281 keren
Re: oil leak
Wrenchmonkey schreef: ↑28 nov 2022, 15:06 Could you show me some examples of that modification for the indirect gear shifting mechanism?
- Bijlagen
-
- D6C1E7CD-9286-419E-AE77-C849FAF99B4B.jpeg (284.06 KiB) 553 keer bekeken
-
- D8BF0CD1-BD8D-4A94-992C-B1CB74352299.jpeg (206.37 KiB) 553 keer bekeken
- Enzo-tvdzijden
- Expert
- Berichten: 60394
- Lid geworden op: 27 nov 2002, 21:55
- Locatie: Gem. Leidschendam/Voorburg
- Gegeven waarderingen: 966 keren
- Ontvangen waarderingen: 2281 keren
Re: oil leak
this part must be smooth
This two gives leakage !!!!
This two gives leakage !!!!
- Bijlagen
-
- 3E0DD96D-B0B8-4E0B-B60B-D0BBA2426A5B.jpeg (154.3 KiB) 544 keer bekeken
-
- 3BFD4AB5-10E7-4BD5-9A0E-904A37A75B92.jpeg (256.94 KiB) 551 keer bekeken
Laatst gewijzigd door Enzo-tvdzijden op 28 nov 2022, 18:03, 1 keer totaal gewijzigd.
- Enzo-tvdzijden
- Expert
- Berichten: 60394
- Lid geworden op: 27 nov 2002, 21:55
- Locatie: Gem. Leidschendam/Voorburg
- Gegeven waarderingen: 966 keren
- Ontvangen waarderingen: 2281 keren
Re: oil leak
Or this nice one
- Bijlagen
-
- DB38F6F3-F981-4A42-A257-7EDF428AADFE.jpeg (122.55 KiB) 517 keer bekeken
-
- Berichten: 6
- Lid geworden op: 28 nov 2022, 02:52
- Gegeven waarderingen: 0
- Ontvangen waarderingen: 0
Re: oil leak
Thanks a lot. I see im gonna have a lot of work ahead, specially on the mill if i cant set the case on the lathe.
Cheers
Cheers